A human hair is about .0040” thick. Martindale Gaylee solid carbide saws can be manufactured as thin as .0020” which is half the thickness of a human hair. This extreme miniaturization is made possible through their numerous years of experience.
At the other end of the spectrum, solid carbide saws can also be made as thick as 1.000” with O.D.’s typically ranging from .250” to 7.500” (6.35mm to 190mm) and tighter than standard tolerances are also available.
Keep in mind that all solid carbide saws 2” diameter and larger are manufactured with a standard hub and round key.
Martindale Gaylee has a dedicated team of saw-makers unparalleled the world over. From saws to cutting knives to slitters, slotters and cutters...we’re prepared to work with you on your specific application.
The miniature saw shown on the left above has an O.D. of 3⁄4” with 18 precision teeth. The saw shown on the right has an O.D. of 1⁄2” with 14 precision teeth. Gaylee takes pride in producing precision saws unsurpassed by any other manufacturer for your application.
Get in touch with us with any questions about solid carbide saws!
compiled & edited by Bernard Martin
As more and more of our customers are using Martindale Gaylee Circular saws we put together this guide to the commonly asked questions such as "Is there a rule-of-thumb for the number of teeth?" or "How much side clearance should I have?" Here we cover a lot of the fundamentals of selecting the right circular saw blade configuration, some tips, tricks, and troubleshooting for when things go wrong.
Circular Saw Feed Rates
These are general cutting speed recommendations for circular saws used in metalcutting from Martindale/Gaylee. The may vary from application to application but are basically some general suggestions starting parameters when using high speed or carbide saws.
Selecting the Proper Number of Teeth in Your Metalcutting Saw
Generally speaking, deep cuts and soft material require fewer teeth for chip clearance and stronger teeth (landed).
Thin material requires more teeth, but keep-in-mind that at least 2 teeth on the blade need to be engaged in cut. Hard materials and narrow slots (under .025”) likewise require more teeth.
Hard Materials require more teeth, and give a smoother cut, but at a much lower production rate.
Alternately beveled teeth keep chips from sticking in the cut and in the tooth gullets.
And Remember that there should be at least 2 teeth engaged in the cut at all times.
Rake Angles and Side Clearance Angles
Just as in an end mill or a band saw blade, a rake angle is the term used to describe the direction of the blade’s teeth, as referenced from the rotation and central axis of a saw blade. If you imagine a line going from the exact center of the blade to each tooth, having the front of the tooth directly on that line would be a zero degree rake angle. The rake angle of the blade is described in comparison to that imaginary line.
A positive rake angle meana that the teeth are angled more towards the angle of rotation, while a negative rake angle would mean that they are angled backwards, away from the direction of rotation. Generally speaking, the preferred rake angle is:
SIDE CLEARANCE (Tangential Clearance Angle)
This is also known as dish or hollow grind. You measure down the side of the tip and the difference it is the difference between front and back. As you cut, material it gets compressed and springs back after the cutting edge passes.
A steep side clearance angle gives plenty of room for the material to expand and prevents thermal expansion of the base material. Keep in mint that a very flat side clearance angle can provide a smoother cut in some materials. For stainless steel and tenacious metals such as copper, zinc, tin or lead an increase in the side clearance is desirable as these materials tend to "spring back" (thermal expansion) on the blade.
Why do Circular Saw Blades Break?
It's commonly known that when saw thickness is less than 0.125″, keyways can cause stress risers and cracks. That is why washers are often used. However, Breakage, Wobble and Rubbing problems are often caused by how the washers are mounted on either side of saw.
Remember, washers drive the saw in the absence of a drive key. They must always be clean, flat and bur-free. A speck of dirt will let saws wobble and cut oversize.
If a saw breaks, it may score the washers. Always check for scoring marks around saw hole for dirt, chips or grit. Shiny spots, as small as a pinpoint, indicate that chips where imbedded under washers.
Circular skid marks indicate the nut was not tight.
Saw Blade Teeth most often break as a result of:
NOTE: HSS saws will turn colors as they heat during cutting. A straw color is the limit. The saw will lose its temper when it starts turning blue.
Technical Support Blog
At Next Generation Tool we often run into many of the same technical questions from different customers. This section should answer many of your most common questions.
We set up this special blog for the most commonly asked questions and machinist data tables for your easy reference.
If you've got a question that's not answered here, then just send us a quick note via email or reach one of us on our CONTACTS page here on the website
Our technical section is written by several different people. Sometimes, it's from our team here at Next Generation Tooling & at other times it's by one of the innovative manufacturer's we represent in California and Nevada.
Next Generation Tooling
10240 Cavalletti Drive
Sacramento CA 95829
© 2022 Next Generation Tooling, LLC.
All Rights Reserved
Created by Rapid Production Marketing